用過卷簾門的業主應該有這樣一個疑問，就是用了一段時間后，為了防止出現問題，需要在使用期間做些什么呢？今天讓我們跟濟南卷簾門廠家一起來講講。

The owner who has used the rolling shutter door should have a question, that is, after using it for a period of time, what should be done during the use to prevent problems? Today, let's talk with Jinan roller shutter door manufacturers.

1.使用清潔窗簾布時，很容易用硬幣劃傷表面。當污漬太重時，可以使用清洗，牙膏和特制清洗。去污后，用清水擦拭，然后晾干。正確的清潔方法可以讓鋁合金卷簾門始終保持明亮如新。

1. When using the cleaning curtain cloth, it is easy to scratch the surface with coins. When the stain is too heavy, you can use cleaning, toothpaste and special cleaning. After decontamination, wipe it with clean water and then dry it. The correct cleaning method can keep the aluminum alloy roller shutter door bright as new.

2.注意棱角不要擦太多，否則會造成棱角表皮脫落。

2. Be careful not to rub too much edges and corners, otherwise the edges and corners will fall off.

3.使用前，門體須經過工作人員的多面調試后才能操作

3. Before use, the door body must be debugged by professional staff before operation

4.當卷簾門在運行時，不允許有兒童或物品在門下，以免在運行過程中傷害兒童或物品。

4. When the rolling shutter door is in operation, children or objects are not allowed under the door to avoid injury to children or objects during operation.

5.操作時觀察是否有異常噪音。如果有異常噪音，有必要通知人在維護進行保養

5. Observe whether there is abnormal noise during operation. If there is any abnormal noise, it is necessary to notify the professional person for maintenance

6.當電動機熱保護連續動作時，應查明故障是否來自電動機或過載或保護裝置整定值過低，排除故障后方可投入運行。

6. When the thermal protection of the motor operates continuously, find out whether the fault is from the motor or overload or the setting value of the protection device is too low, and put it into operation after troubleshooting.

7.應確保電動機在運行過程中潤滑良好。一般電動機器運行約5000小時，也就是說，它應該補充或更換潤滑脂。當運行中發現軸承過熱或損壞時，液壓應及時更換潤滑脂。使用更換潤滑脂時，應舊潤滑油，并用汽油清洗軸承和軸承蓋的油槽，然后在軸承內外圈之間的空腔的1/2(2極)和2/3(4極、6極和8極)中加入ZL-3鋰基潤滑脂。

7. Ensure that the motor is well lubricated during operation. Generally, the electric machine runs for about 5000 hours, that is, it should replenish or replace the lubricating grease. If the bearing is overheated or damaged during operation, the hydraulic pressure shall be replaced with lubricating grease in time. When replacing lubricating grease, the old lubricating oil shall be removed, and the oil groove of the bearing and bearing cover shall be cleaned with gasoline, then ZL-3 lithium base grease shall be added to 1/2 (2-pole) and 2/3 (4-pole, 6-pole and 8-pole) of the cavity between the inner and outer rings of the bearing.

8.由于門體始終處于扭簧的張緊狀態，如果您需要在修理，維護，工作，您需要聯系來自的人員進行操作。

8. As the door body is always in the tension state of the torsion spring, if you need to repair, maintain and work, you need to contact professional personnel to operate.

無論是在家里使用，還是在大型的許多地方使用，比如工業和，卷簾門的作用都不是一件小事。您對此有什么不了解的事情就來我們網站http://www.zzdalvshi.com咨詢吧！

Whether it is used at home or in many large places, such as industries and shopping malls, the role of rolling shutter doors is not a trivial matter. Come to our website if you don't know anything about it http://www.zzdalvshi.com Consult!